mer MITSUBISHI ELECTRIC Issued by: Mitsubishi Electric Europe B.V. - UK Branch Document issue: Ver B, September 2000 Produced by ; - FX Product Marketing Travellers Lane, Hatfleld, Herts, AL10 8XB, UK Author: Laura Parsons Databank - Technical Bulletin EMC Filter for $500 series inverters introduction In common with all variable-speed inverters, the Mitsubishi S500 series can generate significant amounts of Electromagnetic Compatibility (EMC) disturbances. In particular, high frequency (150kHz 30MHZz) disturbances conducted into the mains supply must be controlled if products containing inverters are to comply with European EMC Directive 89/336/EEC requirements. The usual method of controlling these disturbances is to insert a filter into the mains supply to the inverter. A filter has been developed for the S500 series for this purpose. The filter is designed to contral high frequency emissions from the inverter. It will also improve the immunity of the inverter to mains-conducted disturbances. It has no appreciable effect on the generation of immunity to mains harmonics. $500 Filter Specifications Filter designation FR-S5NFSA-0.75K FORK ACL Rated input AC voltage (V) 200 240V (+ 10% - 15%) Rated input/output current (A) 14 (100% load) Overload capacity 150% load 1min, 200% load 1s Leakage current (mA) (500Hz) 45 Electric strength AC2000V iminute, AC2400V 5 seconds Surge 5000V 1.2 42s peak, 50 zs (5 times) Ambient temperature -10 to 50 C Environmental Storage temperature -20 to 65C Condition Ambient humidity 90% RH or less (without dew condensing) Mains conducted performance (at 14.5kHz) Curve A (industrial) with 5m output cable Curve 'B (residential) with 1m output cable Product Diagram input pawer supply terrnii va) DAOCk Terminal black cover? pg Accessories: Mounting screws M4x10..._...... 4 Earth Clamp (P clip)...............1 Aecassanos ER SENFSA-D 75K, FRLSSNESB.O.| Terminal block must be attached when {perce mores, MAxtQ =~ 226+ 4 Earth Clanp (P clip) FA-SSNFGA.1.5K, FR-S6NFSB-1.5 Mannting screws Maxt4-------- 5 CERrth Clamp (P cip)-errer cred werner Gribla 1a connect inerter power The filter and inverter is hot when power Black Gonnect lo termine! L4 Blue; Gonnact to tormanal N using the filter. e Do not switch power on before connecting the inverter power connection cables for the inverter. is on and for a short time when power is off. Title: EMG Fitter for S500 series Inverters Page 1 of 2 Keywords: $500 series, Filters. EMC, European directives TOTAL P.@3 MITSUBISHI ELECTRIC issued by: Mitsubishi Electric Europe B.V, - WK Branch Document issue: Ver B, September 2000 _ Produced by : - FX Product Marketing Travellers Lane, Hatfield, Herts, AL10 8XB, UK ' Author: Laura Parsons | Databank - Technical Bulletin Filter Installation aer The filter can be attached using either a footprint (fig 1.) ar a bookshelf (fig 2.) (fig 1. )- Method for installation on rear panel of inverter. (Vibration: 5.9 m/s) (fig. 1} Method for installation in parallel with inverter. (Vibration: 2.4m/s?) rine one = ASB eq * Vpting seme (a The filter is attached to the inverter using the M4screws provided as shown. Wiring to the filt Warning: Care should be taken to avoid risk of electric shock. ae The mains cable is secured as shown, P : : Shleiged cabia pe __- Pip The inverter-motor wiring can be a powerful ay pehckagiinia the stieled tc) thes litter noise source. Tomoko Whichever method of installation is used, use a'P clip to ensure stability of the mains cable. Wiring in parallel with inverter P clip Directly connect the shiald to the filter with the P cp. / Stelios cable + To motor aeeeene-paees rf Title: EMC Filter for $500 series inverters Page 2 of 2 Keywords: $500 series, Filters, EMC, European directives TOTAL P.@1